|
The Ford Thames 400E is a commercial vehicle that was made by Ford UK and introduced in 1957. Production of the range continued until September 1965, by which time a total of 187,000 had been built. ==History== By the mid 1950s, Ford lagged well behind the competition in the light commercial market. The model still on offer until 1957 was the trusty but antiquated Fordson E83W, released in 1938. Studies were therefore made of the competition in this sector, with the Morris Commercial 10 cwt and 15/20 cwt models, of prewar design; Austin 10 cwt, and later their 25 cwt; Trojan 15 cwt van; and the Bedford 10/12 cwt model all coming in for scrutiny. Taking a design lead from the US parent, a well overdue new 10/12/15 cwt range was therefore decided upon, to be of the forward control type all based on the same 'outrigger' chassis. With regard to this 'outrigger chassis', Cab and chassis windscreen variants, (subsequently described as 'open' back) differed from the van, estate car, and express bus body models, (subsequently described as 'closed' back) models by the addition of an extra rear crossmember to support the spare wheel carrier and to close the rear ends of the chassis horns. On the 'closed' back models the nature of the rear bodywork meant the rear crossmember could be omitted for this purpose. Another subtle difference between the 'open' back models Vs. 'closed' back models was the method of body attachment to the chassis. On 'open' back models the rear chassis outriggers were designed to accept customers' own coachwork either attached via welded cleats or bolted directly. This bodywork be it a pickup buck or say an ambulance body typically added extra stability to the rear chassis however should not be considered essential because the chassis design is constructed so as to be sturdy enough without. To promote ease of conversion, 'open' back models had cab bodywork that bolted to the chassis and could therefore be removed easily during the conversion process giving better access to the chassis under. On 'closed' back models this flexibility for conversion was not considered necessary as customers buying an enclosed van type vehicle were unlikely to require access to the chassis in a similar fashion as 'open' back purchasers. More likely modification of the bodywork undertaken by 'closed' back purchasers would constitute removal of roof panels for elevating sections or the addition of windows as can be seen in many motor caravan conversions for example. As a result it was decided that steel bodywork and cab sections could be welded directly to the chassis in places mainly for ease of construction and consequently adding additional stability to the chassis in a similar fashion to that of a coachbuilder converting an 'open' model. It should be stressed that this welded bodywork was not essential for maintaining acceptable levels of torsional chassis strength, the chassis design of the 'closed' back models should not be considered as 'unitary' for this reason. The correct definition in this case is a 'body reinforced separate chassis'.〔 A wheelbase of was chosen, upon which was accommodated a van body of capacity, After some discussion, independent front suspension was sanctioned, but not of the MacPherson strut type which Dagenham had pioneered in the monocoque passenger car applications for which it had been specifically designed in the first place. This system was considered, but its inclusion in the forward control, forward entrance van would, primarily because of the strut height, have placed serious restrictions on cab design particularly in respect of entry. Instead, a system of coil springs and transverse wishbones was agreed upon. An ideal engine and transmission existed amongst Dagenham's passenger car range, this being the Consul's 1703 cc ohv engine, with its associated three speed gearbox with synchromesh between the upper two ratios and a column gearchange mechanism, and the two pinion differential three quarter floating final drive. The low compression (6.9: 1) version of this engine, developing at 4400 rpm was chosen, with the Consul's regular high compression cylinder head (7.8:1) being optional on the new van, A further option was to be the Perkins 4/99 diesel, this being a 1.6 litre four cylinder unit producing only , therefore somewhat marginal from a performance viewpoint but offering useful long term economies over the petrol engine. From January 1963 an improved version of the 1703 cc engine was introduced for the range being uprated to in low compression form, while for premium petrol users a high compression head was offered which gave this Zephyr 4 unit an output of . A four speed all synchromesh gearbox was also available from this time, and if fitted a heavy duty back axle with a four pinion differential was specified. Production commenced in September 1957, with the model being announced as the Thames 400E series. A bold Thames nameplate appeared on the front beneath which was a circular emblem containing the appropriate figure identifying the vehicle's capacity class. The new model quickly met with widespread approval, and passenger transport use was soon being catered for with the availability of an 8/10 seater estate car derivative, and a 12 seat minibus based on the 15 cwt model. The success of the estate car variant was such that it later became available in a De Luxe configuration, complete with chrome plated overriders for its front bumper, chrome side mouldings and window trims, and dual exterior mirrors. In March 1965, when the D series trucks were introduced, all commercial vehicle models took the Ford name so the 400E then appeared with a Ford nameplate on the front panel. The range did not continue in this guise for very long, the last models being built in August 1965 pending the introduction of a new range of vans which had been tested and developed since about 1963 under the codename of Redcap. 抄文引用元・出典: フリー百科事典『 ウィキペディア（Wikipedia）』 ■ウィキペディアで「Ford Thames 400E」の詳細全文を読む スポンサード リンク
|